Test Steps:=>
1.Client:
Users: Administrator/Guest(X)
Print & Fax: Server printer need to remove
- Driver
3in1: The first one is scanner, the second is printer;
4in1: The first one is scanner, the second one is printer (include XPS), and the last one is fax printer.
- Server: If you can’t add the found computer, please remove it and refresh, then add it again.
- Add rules: USB->Manual->Printing(except “Print Driver DevMode” & “Print Driver Stress Test”
- Disable Enable With IO: The client system will restart, and you must enter the user name and password at the first time.
- “Print Driver DevMode” & “Print Driver Stress Test” ,change the port to “Null” and check the printer is online every time.
DTM Scanner测试:
“WIA Transfer Test”测试不过之后跟james 讨论的解决办法。
Steps:
1. 完成client和server端架构,添加一个测试项(任意的);
(备注:/*先跑这一项,第一次client端会进入到DTMAdministrator用户。*/)
2. 跑完该项后,将client端logoff,然后选择Administrator进入;
(备注:/*选择Administrator的原因是DebugView[SW]必须要在Administrator权限下才可以打开。*/)
3.待进入Administrator下,将Debugview[SW/FW]两个全部打开;
4.从Server端添加“WIA Transfer Test”,观察client端。
(备注:/*这一项DTM测试总共会有50个case,前25项是平板扫描,不会出现问题。后25项是ADF扫描,
这时候就需要在ADF放纸,并且测试过程会出现”paper jam”。出现”paper jam”的时候,将ADF盖子
打开,取出纸,等机器恢复正常后再放入纸。点击“OK”,机器可以继续扫描。
********这一过程中,只要是CMD没有出现红色字体这一项就可以测试Pass。*/
XPS Printer
1.测试添加项目按照上述从左到右的顺序进行添加;
2. Vista系统记得装上"C++", Server 2008的系统装上".NET";
3.由于XPS Print Driver手动项(MANUAL)的较多,并且不是点击了"Pass"就完成,所以这些项目要时刻去关注;
4.Printer Driver DevMode Corruptor Test & Print Driver Stress Test两项测试时间较长,并且不是很容易就过,所以建议分开来一项一项去添加;同时,未必改了“NullPort”就可以过,跑的时候还要时刻去确认以下端口有没有被在测试的时候自动改变了。
5.Device Path Exerciser在完成打包时一般都可以过,所以也建议留到最后添加;
6.测试"Disable Enable With IO"&“Common Scenario Stress With IO”&“Sleep Stress With IO”等项目,Vista以上系统会需要输入用户名和密码的,所以就需要随时跟踪测Client电脑, 保证进入系统。
7.测试完成后仔细检查cpk包:a.确认所有项目都有列在测试结果里面(尤其是USB项容易忽视);
b.系统及版本的确认(Ser08 R2 datacenter x64bit显示的是Win 7 server x64bit)。
Print & Fax
- Ser08 datacenter 64bit系统只有固定几台电脑可以测过DP项;
- Vista以上系统测试IO项时会重启电脑,并需要手动输入用户名和密码进入,时间还有一定限制;
- DevMode & Strees Test要确保能跑起来,通常如果没有程序没有动,并且在开始菜单进入Print & Fax无法进入时就说明这一项就跑不起来了。关掉停止的程序,再进入“Print & Fax”你会发现Printer or Fax不见了,或是状态改为了Offline.这种情况就添加一个Null端口,改成Online,重新跑就可以了。